当前位置:» 机械及行业设备 » » 自吸泵 » 进口自吸泵(欧美品牌)

进口自吸泵(欧美品牌)

更新时间:2018-06-02 09:40:15 信息编号:8943673 浏览:1次
  • 供应商

    上海秉奇阀门有限公司 商铺

  • 认证 营业执照已认证
  • 报价面议
  • 最小起订大量
  • 发货期限自付款之日起30日内发货
  • 供应能力88888台台/每月
  • 样品不提供
  • 所在地上海 上海 徐汇区 龙漕路51弄
  • 联系电话021-51698378
  • 手机号135 2426 9805
  • 联系人黄天翔
咨询自吸泵 产品,请说在传众网看见,优惠多多

 

产品详情

英国GRIMM格林进口自吸泵 UK GRIMM Imported self-priming pump


英国GRIMM格林进口自吸泵概述: 

          进口自吸泵是根据英国格林有关技术资料经吸收、消化、改进后研制而成的节能泵类产品。该泵属自吸式离心泵,它具有结构紧凑、操作方便、运行平稳、维护容易、效率高、寿命长、并有较强的自吸能力等优点。管路中不需安装底阀,工作前只需保留泵体内储有定量引液即可。因此简化了管路系统,又改善了劳动条件。

英国GRIMM格林进口自吸泵结构说明及工作原理: 

             进口自吸泵,主要由泵体、叶轮后盖、机械密封、泵轴、轴承座、进口阀、气液分离管、加水阀门,进、排接管等 组成。
          泵的工作原理,该泵均采用轴向回液的泵体。原理由吸入室、储液室、涡卷室、回液孔、气液分离室等组成。
          泵正常起动后,叶轮将吸入室所存的液体及吸入管路中的空气一起吸入,并在叶轮内得以混合,在离心力的作用下,液体夹带着气体向涡卷室外缘流动,在叶轮的外缘上形成有厚度的白色泡沫带及高速旋转液环。气液混合体通过扩散管进入气液分离室。此时,由于流速突然降,较轻的气体从混合气液中被分离出来,气体通过泵体吐出口继续上升排出。脱气后的液体回到储液室,并由回流孔再次进入叶轮,与叶轮内部从吸入管路中吸入的气体再次混合,在高速旋转的叶轮作用下,又流向叶轮外缘▪▪▪▪▪▪。随着这个过程周而复始的进行下去,吸入管路中的空气不断减少,直到吸尽气体,完成自吸过程,泵便投入正常作业。

英国GRIMM格林进口自吸泵技术参数: 

流       量:3.2-600m3/h
扬       程:8-80m
口       径:进口直径:25-300mm
                  出口直径:25-250mm
吸       程:5-6.5m
自吸性能:1.3-2.5min/5m
转       速:1450r/min、2950r/min
功       率:0.75-132kw

英国GRIMM格林进口自吸泵应用范围: 
1、适用于城市环保、建筑、消防、化工、制药、染料、印染、酿造、电力、电镀、造纸、工矿冲洗、设备冷却等。
2、装上摇臂式喷头、又可将水冲到空中后,散成细小雨滴进行喷雾,是农场、苗圃、果园、茶园的良好机具。
3、适用于清水、海水及带有酸、碱度的化工介质液体和带有一般糊状的浆料(介质粘度≤100厘珀、含固量可达30%以下)。
4、可和任何型号、规格的压滤机配套使用,将浆料送给压滤机进行压滤的理想配套泵种。

UK GRIMM Imported self-priming pump summary:

         Imported self-priming pump is based on the relevant technical data of the United Kingdom Green, absorbed, digested, improved, developed from energy-saving pump products. The pump is a self suction centrifugal pump. It has the advantages of compact structure, easy operation, stable operation, easy maintenance, high efficiency, long service life and strong self suction capacity. Do not need to install the valve in the pipeline, keep working just before the pump body fluid can be stored with quantitative cited. Therefore, the pipeline system is simplified and the working conditions are improved.

UK GRIMM Imported self-priming pump structure description and working principle:

           Imported self-priming pump, mainly by pump body, impeller rear cover, mechanical seal, pump shaft, bearing seat, inlet valve, gas-liquid separation pipe, water valve, intake, discharge pipe and so on.

        The working principle of the pump is that the pump adopts axial return liquid pump. The principle is composed of suction chamber, liquid storage room, scroll chamber, liquid return hole, gas-liquid separation chamber and so on.

        Pump normal starting, the impeller room will suck the liquid suction pipe and the air suction, and can be fully mixed in the impeller under the action of centrifugal force, the liquid entrainment from the gas chamber outer scroll flow, the formation of a certain thickness of the white foam and high-speed liquid ring in the impeller on the edge. The gas-liquid mixture passes through the diffusion tube into the gas-liquid separation chamber. At this point, as the flow rate suddenly decreases, the lighter gas is separated from the mixture gas, and the gas continues to rise and discharge through the pump body. After the degassing of liquid to the liquid storage chamber, and the reflux hole again into the gas and the impeller, impeller sucked from the suction pipe again mixed in high speed rotating impeller role, and flows to the outer edge of the impeller feels feels feels feels feels feels. As the process goes on and on, the air in the suction line continues to decrease until the gas is exhausted and the self-priming process is completed, and the pump is put into normal operation.

UK GRIMM Imported self-priming pump technical parameter:

Flow rate: 3.2-600m3/h

Lift: 8-80m

Caliber: Inlet diameter: 25-300mm

             Outlet diameter: 25-250mm

Range of suction: 5-6.5m

Self suction performance: 1.3-2.5min/5m

Speed: 1450r/min, 2950r/min

Power: 0.75-132kw

UK GRIMM Imported self-priming pump application range:

1. Suitable for urban environmental protection, building, fire, chemical, pharmaceutical, dye, printing and dyeing, brewing, electricity, electroplating, paper making, industrial and mining washing, equipment cooling, etc..

2. With rocker arm sprinkler, and water can be washed into the air, scattered into small raindrops spray, is a farm, nurseries, orchards, tea plantations good tools.

3. Application of chemical liquid in water, seawater and with acid, alkalinity and general mushy slurry (medium viscosity less than 100 per cent Perot, solid content is below 30%).

4. It can be used in conjunction with any filter press of any type or size, and will be the ideal type of pump for the press filter.


产品关键词: 自吸泵
产品所属分类: 机械及行业设备/ 泵/ 自吸泵
企业介绍
上海秉奇阀门有限公司是一家集科研、产品开发、制造.销售、售后服务于一体的高新技术企业,位于享誉国际盛名城市--上海,具有实力的国内合资企业。本公司具有强大的设计、生产.销售和服务队伍。生产历史悠久、质量体系完善,测试手段齐全,生产工艺先进,确保产品质量有保障免客户后顾之忧。产品采用国外先进技术设备,严格按照标准和行业标准,以及API、DIN、JIS、ISO等国际标准生产制造各种阀门。 本公司专业生产:球阀、蝶阀、闸阀、截止阀、止回阀、针型阀、过滤器、电磁阀、刀型闸阀、呼吸阀、阻火器、柱塞阀、排污阀、排泥阀、疏水阀、放料阀、排气阀、衬氟阀门、旋塞阀、调节阀、减压阀、安全阀、水力控制阀、平衡阀、液压阀、卫生级阀门、液化气专用阀、视镜等等。材料有:铸铁、碳钢、不锈钢、合金钢和特种材料等,其中铸件有:CF8、CF3、CF3M、WC5、WC6、WC9、WCB、LCB、LC3等,锻件有:A105、F11、F22、F304、F316、F304L、F316L等。压力等级:150-2500LB、PN1.0-42MPa,温度:-196~600 ℃,口径1/4〝-68〝、2㎜-1800㎜,驱动方式:手动、齿轮传动、电动、气动、液动、蜗轮传动。采用标准:API、ANSI、BS、JIS、DIN、NF、JB、HG、SH、GB等标准。本公司为了更满足用户的需求,设有销售二部,代理销售进口阀门有:美国进口阀门、日本进口阀门、英国进口阀门、德国进口阀门等品牌产品。 上海秉奇阀门有限公司自创办以来,对产品进行不断优化锐意创新,努力开发以国代进,打造“秉奇””的方针。大胆引进人才,狠抓管理和质量,成功采用了先进的计算机管理和CAD设计,建立起一套完整的质量保证体系,雄厚的技术品,愿与各界新老朋友携手共进,竭诚合作,回报广大用户对我们支持与厚爱。力量、精良的生产设备、先进的检测手段、精湛的生产工艺,结合多年的生产经验以及规范科学的管理,使我厂的每一个产品质量都得以保障,从而得到了众多客户的认可,阀门产品受到广大用户的好评,低廉的价格,周到品牌。本公司产品规模齐全品种繁多,生产能力强,营销手段活;主要产品不断远销东南亚地区和国内各地,深受 化工、石油、石油化工、环保、给排水、冶金、电力、造纸、制药、印染、海水淡化、食品酿酒、暖通等行业用户的一致好评。秉着:“品质优异、客户满意”的经营理念,为你提供优良的产品和完善的服务。是您的诚挚的朋友。多年来,本公司奉行“质量,用户上”的宗旨,坚持“依靠科技求发展,依靠质量求生存,改善管理求效益,争创促销售的售后服务,拓宽了我厂的销售渠道,产品销售除覆盖全省各地。 热情欢迎各行各业新老用户来函、来电,光临我厂洽谈业务。我们将以强劲的发展之势,高品质的产品,愿与各界新老朋友携手共进,竭诚合作,回报广大用户对我们支持与厚爱。
联系方式
上海秉奇阀门有限公司
联系人 : 黄天翔
手 机 : 135 2426 9805
电 话 : 021-51698378
传 真 : 021-51698378
Email : bqvalves@126.com
Q Q : 673088832
地 址 : 上海 上海 徐汇区 龙漕路51弄
邮 编 : 200235
传众商铺 : 34627128.czvv.com

快捷留言

*您的称呼:
*您的电话:
Email:
*咨询内容:
您也可以通过点击此处发布您的采购需求让产品供应商主动联系您!
免责声明:
进口自吸泵(欧美品牌)产品由上海秉奇阀门有限公司自行上传维护,内容的真实性、准确性、合法性由发布企业负责,传众对此不承担任何保证责任!
© 2024 传众  czvv.com