进口齿轮油泵(欧美品牌)

英国GRIMM格林进口齿轮油泵 UK GRIMM Imported gear pump

英国GRIMM格林进口齿轮油泵概述： 
         进口齿轮油泵又称进口齿轮式输油泵，适用于输送各种不含固体颗粒和纤维，有润滑性的液体，介质温度不高于300℃，粘度为5×10^-5～1.5×10-3m2/s，如柴油，润滑油，原油等，配用铜齿轮和防爆电机可输送汽油，苯等闪点液体。不锈钢材料的泵体可用于食品工业输送饮料，食用油，牛奶等。
         该泵在输油系统中可用作传输、增压泵；在燃油系统中可用作输送、加压、喷射的燃油泵；在一切工业领域中，均可作润滑油泵用。泵体材料根据客户需要可选用铸铁，铝合金和不锈钢。轴封有骨架油封，填料密封，机械密封供选择。

英国GRIMM格林进口齿轮油泵结构特点： 
         进口齿轮油泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。齿轮经热处理有较高的硬度和强度，与轴一同安装在可更换的轴套内运转。泵内全部件的润滑均在泵工作时利用输出介质而自动达到。
　　  泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力小，因此轴承负荷小，磨损小，泵效率高。
　　  泵设有安全阀作为超载保护，安全阀的全回流压力为泵额定排除压力的1.5倍，也可在允许排出压力范围内根据实际需要另外调整。但注意本安全阀不能作减压阀的工作，需要时可在管路上另行安装。

英国GRIMM格林进口齿轮油泵主要参数：
流       量：18.3-9600L/min
排出压力：0.3-1.45MPa
口       径：25-350mm
吸       程：5m
转       速：740-1420r/min
功       率：1.5-250kw
电       压：220/380V
材       质：铸铁、铝合金、不锈钢

英国GRIMM格林进口齿轮油泵适用范围：

在输油系统中可用作传输、增压泵；

在燃油系统中可用作输送、加压、喷射的燃油泵；

在一切工业领域中，均可作润滑油泵用。

UK GRIMM Imported gear pump summary:

        Imported gear pump is also called imported gear type oil pump, suitable for conveying various solid particles and fiber, a lubricating liquid, the temperature of the medium is not higher than 300 DEG C, the viscosity is 5 * 10-5 to 1.5 * 10-3m2/s, such as diesel oil, lubricating oil, crude oil, with copper gear and explosion-proof electric machine can transport gasoline benzene, such as low flash point liquid. Stainless steel pump body can be used in the food industry to transport beverages, cooking oil, milk and so on.

        The pump can be used as a transmission and booster pump in the oil transportation system. It can be used as fuel pump for transportation, pressurization and injection in the fuel system. It can be used as a lubricating oil pump in all industrial fields. Pump material, according to customer needs, can choose cast iron, aluminum alloy and stainless steel. Shaft seal has skeleton oil seal, packing seal, mechanical seal for choice.

UK GRIMM Imported gear pump structure characteristics:

        The imported gear pump mainly consists of gear, shaft, pump body, safety valve and shaft end seal. The gear has higher hardness and strength after heat treatment, and it is installed with the shaft in the replaceable axle sleeve. The lubrication of all parts in the pump is automatically reached by using the output medium when the pump is working.

        The pump has reasonable design of the oil and the oil return groove is a gear in the work under minimum torque force, so the bearing load is small, small abrasion, high pump efficiency.

        The pump is equipped with a safety valve as overload protection, the total return pressure of the safety valve is 1.5 times of the rated pump pressure, and can be adjusted in the allowable discharge pressure range according to the actual needs. But note that the safety valve can not be used for long-term work of pressure reducing valve, when necessary, can be installed on the pipeline.

UK GRIMM Imported gear pump technical parameter:

Flow rate: 18.3-9600L/min

Discharge pressure: 0.3-1.45MPa

Caliber: 25-350mm

Range of suction: 5m

Speed: 740-1420r/min

Power: 1.5-250kw

Voltage: 220/380V

Material: cast iron, aluminium alloy, stainless steel

UK GRIMM Imported gear pump scope of application:

In the oil transportation system, it can be used as a transmission and booster pump;

A fuel pump used in a fuel system for transportation, pressurization, and injection;

It can be used as lubricating oil pump in all industrial fields.